UNITIKA UNITIKA PLASTICS DIVISION
Japanese Chinese
Printing Tips
Nylon Resin U-polymer TERRAMAC Unilate Elitel
Grade List
General Properties
Molding Condition

Applications

To Website of
TERRAMAC in General
TERRAMAC > General properties   To Top Page
[UNITIKA TERRAMAC]

General properties of TERRAMAC resins
<Injection grades>
Print Table on A4 Paper
Item
Test method
ISO
Unit 
Basic grade
TE-2000
High-
impact
grade
TE-1030
High-
impact
grade
TE-1070
Heat-
resisting
grade
TE-7000
Heat-
resisting
grade
TE-7307
Heat-
resisting
grade
TE-7300
High-
durability
grade
TE-8210
High-
durability
grade
TE-8300
Appearance
-
-
Tran
sparent
Opaque
white
Opaque
white
Opaque
white
Opaque
white
Opaque
white
Opaque
white
Opaque
white
Density
1183
-
1.25
1.24
1.24
1.27
1.42
1.47
1.42
1.47
Melting point
-
°C
170
170
170
170
170
170
170
170
Breaking
strength
527
MPa
63
51
34
70
54
54
50
56
Tensile
elongation
527
%
4
170
200<
2
2
1
2
1
Bending
strength
178
MPa
106
77
50
110
85
98
90
104
Bending
modulus
178
GPa
4.3
2.6
1.4
4.6
7.5
9.5
6.8
9.3
Charpy impact
strength:
With notch
179
kJ/m2
1.6
2.3
5.6
2.0
2.5
2.4
4.0
2.8
Deflection
temperature
under
load of 0.45 MPa
75
°C
58
51
54
110
120
140
120
140
Molding shrinkage
-
%
0.3~0.5
0.3~0.5
0.3~0.5
1.0~1.2
1.0~1.2
1.0~1.2
1.0~1.2
1.0~1.2
* The data above are typical values of test pieces determined by our tests,
and are not intended to guarantee the properties of resins in a particular application.
<Extrusion, blow, and foam sheet grades>
Item
Test method
ISO
Unit 

Basic grade
TP-4000

Soft
TP-4030

Foam
HV-6250H
Appearance
-
-
Tran
sparent
Opaque
white
Opaque
white
Density
1183
-
1.25
1.24
1.27
Melting point
-
°C
170
170
170
Breaking
strength
527
MPa
66
50
69
Tensile
elongation
527
%
5
44
2
Bending
strength
178
MPa
108
71
111
Bending
modulus
178
GPa
4.6
2.4
4.7
Charpy impact
strength:
With notch
179
kJ/m2
1.6
2.6
1.9
Deflection
temperature under
load of 0.45 MPa
75
°C
59
52
120*1
Molding shrinkage
190°C
2.16kg
g/10min
3~5
3~5
1~3
* The data above are typical values of test pieces determined by our tests,
and are not intended to guarantee the properties of resins in a particular application.
*1 This data is a temperature shown in molding at a predetermined die temperature(110°C).
In molding with a die of a lower temperature, the temperature is approx. 60°C.

To Page Top